Properties
- Type – 2-K Urethane / Acrylic Hybrid
- Form – Opaque Liquid
- Odor – Bland
- Color – Milky White
- Weight Per Gallon – 8.60 Lbs. (Part A)
- pH – 8.65
- V.O.C. (as used) – 231 g/l
- Hardness (7 day Konig) – 130 Secs.
- Moisture Resistance – Non-Whitening When Exposed to Water
- Slip Resistance – UL-Classified
- Coverage – 1500-2500 Sq. Ft. Per Gal.
* Properties are typical and subject to usual manufacturing tolerances.
Prep & Mix
PREP:
- Strip conventional floor finish using Xlerate™ (2917FX) following product package directions.
- If the floor is coated with anything other than conventional finish, contact Essential Industries at
(800) 593-1021. These include: OMU, Sealer and Permanent Coating.
- (OPTIONAL*): When floor is dry, polish the floor using a 6000 grit or greater diamond polishing pad on a high speed machine (1500 RPM or higher).
- Do NOT apply T-Rx to a coated surface.
* OPTIONAL instructions are NOT necessary, but they improve final gloss of the coating.
IMPORTANT! Read Before Proceeding
- Pot Life is 3 hours – DO NOT mix more product than you will use in 3 hours.
- This product is NOT strippable.
- Do NOT blend different batches of material together.
- Application vessel and mop heads should be washed between batches of newly mixed material.
- Apply no more than 3 coats in a 24 hour period.
- Allow 6 hours of cure time before allowing traffic on the floor.
- Coverage – 1500-2500 sq. ft. per gallon.
MIXING – Equipment and Materials:
- T-Rx Part A and Part B
- Clean mixing pail
- Fresh water source
- Electric drill
- Drill paddle (3”-4”)
MIXING – Directions:
*NOTE: When following the mixing instructions use:
3500 grams Part A bottle with 203 grams Part B metal canister (included)
- Read all directions and cautions carefully prior to mixing product.
- Equip drill with drill paddle.
- Pour all of Part A into a clean mixing pail.
- Begin agitating part A with drill equipped with drill paddle before adding Part B. Hold paddle at a 45 degree angle with the paddle close to the far edge of the pail when agitating.
- *(See Note above) Next, slowly pour all of Part B liquid into Part A in a stream no wider than the diameter of a pencil. Make note of the time: This should take at least 90 seconds. Ensure Part B container is completely empty.
- Continue to agitate mixed material for an additional 2 minutes.
- Allow material to rest for 5 minutes or until bubbles subside in the pail.
- Rinse empty product packaging with water and dispose of packaging properly.
- Wash drill paddle thoroughly with water to avoid product drying on the paddle.
Application & Maintenance
APPLICATION – Equipment and Materials:
- Properly mixed T-Rx material (see Mixing Directions)
- Application vessel
- KaiMotion bucket for large jobs
- Watering can for small to medium jobs
- Flat mop equipped with a short-nap, microfiber mop head/pad
- Fresh water source
APPLICATION – Directions:
- Read all directions and cautions carefully before proceeding.
- Eliminate air flow from work area by closing windows and doors and turning off fans or HVAC system.
- Pour freshly mixed T-Rx into application vessel.
- To apply T-Rx to floor using a KaiMotion bucket or watering can: Apply a thin bead (4”- 6”) working in sections of 300 sq. ft.
- Using the flat mop applicator, coat the floor as you would with a conventional floor finish.
- Floor must dry for at least 1 hour prior to recoating. If floor appears dry after an hour, conduct a paper test to confirm prior to recoating.
- Rinse mop pad with fresh water thoroughly between coats.
- Wait 90 minutes after applying the last coat. Conduct the paper test to ensure floor is dry, and polish floor with a white polishing pad to accelerate the drying process.
- Polish the floor using a 6000 grit diamond pad on a high speed machine (1500 RPM or higher).
- Polish the floor again with a white polishing pad to even out appearance.
MAINTENANCE – Equipment and Materials:
If applying additional thin coats of T-Rx to traffic lanes (step 3 below):
- Properly mixed T-Rx material (see Mixing Directions)
- Application vessel (KaiMotion bucket or watering can)
- Flat mop equipped with a short-nap, microfiber mop head/pad
- Fresh water source
MAINTENANCE – Directions:
- DAILY: Sweep or dust mop as necessary to remove gritty soil.
- DIRTY FLOORS: Clean with Blue Concentrate (2085FC) or Blue Concentrate SC (4085FC). Follow package directions for proper dilution rates. Rinse and let dry.
- TRAFFIC AREA: Clean with Blue Concentrate (2085FC) or Blue Concentrate SC (4085FC). Follow package directions for best results. Rinse and let dry. Apply additional thin coats of T-Rx to traffic lanes as needed.
Scrub and Recoat
SCRUB & RECOAT – Equipment and Materials:
- Auto scrubber
- Blue pad
- Mop and bucket
- Blue Concentrate (2085FC) or Blue Concentrate SC (4085FC)
- Properly mixed T-Rx material (see Mixing Directions)
- Application vessel
- KaiMotion bucket – for large jobs
- Watering can – for small to medium jobs
- Flat mop equipped with a short-nap, microfiber mop head/pad
*OPTIONAL* Equipment and Materials:
- High speed burnisher
- 6000 grit diamond pad
- White polishing pad
* OPTIONAL equipment and materials are NOT necessary, but they improve final gloss of the coating.
SCRUB & RECOAT – Directions:
- Deep clean floor using Blue Concentrate (2085FC) (2 oz per gallon) or Blue Concentrate SC (4085FC) (1 oz per 2 gallons) and an auto scrubber using a blue pad.
- (OPTIONAL*): When floor is dry, polish the floor using a 6000 grit diamond pad on a high speed machine (1500 RPM or higher).
- Damp mop or autoscrub with Blue Concentrate (2085FC) (2 oz per gallon) or Blue Concentrate SC (4085FC) (1 oz per 2 gallons) to pick up dust and debris.
- Apply 2 coats of T-Rx, waiting at least an hour and making sure the 1st coat is dry before applying 2nd coat.
- Wait 90 minutes after applying the last coat. Conduct the paper test to ensure floor is dry, and polish floor with a white polishing pad to accelerate the drying process.
- Polish the floor using a 6000 grit diamond pad on a high speed machine (1500 RPM or higher).
- Polish the floor again with a white polishing pad to even out appearance.
*OPTIONAL instructions are NOT necessary, but they improve final gloss of the coating.
CLEANING & RESTORATION – Directions:
- Use Citrus Scrub N Shine (525FR), diluted at 3 to 4 ounces, in a spray bottle.
- Spray and let sit for 5 minutes.
- Buff the floor with an 8,000 grit diamond pad. The floor can be a little damp when buffing starts. It should haze slightly, and then become clear.
- Polish with a white pad for clarity.
Stain Resistance
Terrazzo Test Blocks (3 Coats)
1 Hour Covered Spot Test
Water – No Effect
Skydrol Hydraulic Fluid – No Effect
HCL – No Effect
Kerosene – No Effect
Diesel Fuel – No Effect
Gasoline – No Effect
Windshield Washer Fluid – No Effect
Automatic Transmission Fluid – No Effect
50% Ethanol – No Effect
Betadine (povidine-iodine 7.5%) – No Effect
70% Isopropanol – Slight Softening, Full Recovery
10% Ammonia – No Effect
Red Wine Vinegar – No Effect
Beet Juice – No Effect
Coca Cola – No Effect
Tomato Juice – No Effect
Beer – No Effect
Pickle Juice – No Effect
Mustard – Faint Stain, Full Recovery
Packaging
Not For Sale in the Following States: MN
| Product Code |
Sizes |
UPC Code |
Pack Size (inches) |
Cube (ft) |
Pack Wt. (lbs) |
Full Pallet |
| 152CF |
3 x One F-Style Gallon
(includes Parts A & B) |
783366152049 |
12.75 x 8.75 x 15 |
0.97 |
28.00 |
39 |
- Product Code: 152CF
- Sizes: 3 x One F-Style Gallon (includes Parts A & B)
- UPC Code: 783366152049
- Pack Size (inches): 12.75 x 8.75 x 15
- Cube (ft): 0.97
- Pack Wt. (lbs): 28.00
- Full Pallet: 39
